Blue Seal G50-D Manuel de service

-1- Revision 3/F3601 SERVICE MANUAL G50 / G50-8 GAS RANGE

-10- Revision 3/F3601 3.1.3 OVEN 1) Open oven doors. Push in thermostat knob and rotate anti-clockwise to the PILOT ( ) position. 2) Hold

-11- Revision 3/F3601 SAFETY SYSTEM The purpose of the safety system is to shut off the flow of gas if the flame goes out. It is comprised of the

-12- Revision 3/F3601 4. MAINTENANCE EXTERIOR Clean with detergent. Baked on deposits or discoloration may require a good quality stainless ste

-13- Revision 3/F3601 5. TROUBLE SHOOTING WARNING: ALL INSTALLATION AND SERVICE REPAIR WORK MUST BE CARRIED OUT BY QUALIFIED PERSONS ONLY. 5.1 HOB O

-14- Revision 3/F3601 FAULT POSSIBLE CAUSE REMEDY PILOT BURNER WILL NOT LIGHT No gas supply. Gas pressure too low. Blocked pilot injector. Kn

-15- Revision 3/F3601 5.2 OVEN FAULT POSSIBLE CAUSE REMEDY PIEZO IGNITOR NOT SPARKING Short in high tension lead. (Refer fault diagnosis 6.1.3) P

-16- Revision 3/F3601 FAULT POSSIBLE CAUSE REMEDY MAIN BURNERS WILL NOT LIGHT Wrong size or blocked injectors. Small pilot flame. (Refer fault:Sma

-17- Revision 3/F3601 6. SERVICE PROCEDURES WARNING: ALL INSTALLATION AND SERVICE REPAIR WORK MUST BE CARRIED OUT BY QUALIFIED PERSONS ONLY. SECTION

-18- Revision 3/F3601 6.5 ADJUSTMENT / CALIBRATION ...27 6.5

-19- Revision 3/F3601 6.1 FAULT DIAGNOSIS Short in high tension lead If repeated sparking of the piezo shows intermittent sparking at the elec

-2- Revision 3/F3601 WARNING: ALL INSTALLATION AND SERVICE REPAIR WORK MUST BE CARRIED OUT BY QUALIFIED PERSONS ONLY.

-20- Revision 3/F3601 One screw 6.2 ACCESS 6.2.1 HOB CONTROL PANEL 1) Remove all gas control knobs by pulling away from the control panel. 2) Remo

-21- Revision 3/F3601 6.3 REPLACEMENT - HOB 6.3.1 OPEN BURNER 1) Remove pot-stand/trivet and pot-stand spider from above burner to be replaced.

-22- Revision 3/F3601 Pilot supply tube Two screws Griddle injector Two tabs 6.3.5 GRIDDLE BURNER 1) Remove griddle plate. 2) Unscrew the 3/16"

-23- Revision 3/F3601 6.3.9 GRIDDLE BURNER PILOT THERMOCOUPLE 6.3.10 GRIDDLE BURNER PIEZO IGNITOR 1) Remove control panel (refer 6.2.1). 2) Undo

-24- Revision 3/F3601 H.T. Lead 6.4.1 OVEN H.T. LEAD 1) Open oven control panel (refer 6.2.2). 2) Gain access to the oven burner (refer 6.2.3).

-25- Revision 3/F3601 Burner injector Two screws Three screws Thermostat phial Ignitor nut 6.4.4 OVEN GAS CONTROL 1) Open oven control panel (refer

-26- Revision 3/F3601 Two screws 6.4.7 OVEN PILOT BURNER 1) Gain access to the oven burner (refer 6.2.3). 2) Disconnect the pilot supply tube,

-27- Revision 3/F3601 6.5 ADJUSTMENT 6.5.1 BURNER AERATION Two Screws 6.5.2 RE-GREASING HOB GAS CONTROL 1) Remove gas control (refer 6.3.4). 2) R

-28- Revision 3/F3601 Spindle Figure 6.5.4 4) Apply a suitable high temperature gas cock grease or lubricant such as ROCOL - A.S.P (Anti scuffi

-29- Revision 3/F3601 6.5.6 OVEN PILOT ADJUSTMENT 6.5.7 OVEN THERMOSTAT CALIBRATION Burner pressure test point Figure 6.5.8 4) If the pressure is i

-3- Revision 3/F3601 CONTENTS This manual is designed to take a more in depth look at the G50 gas ranges for the purpose of making the units more u

-30- Revision 3/F3601 6.5.8 DOOR BALL CATCH SETTING A C B E D Figure 6.5.11 10) Replace Torx head screw and release knob. 11) Test oven temperatu

-31- Revision 3/F3601 7. SPARE PARTS PART NO DESCRIPTION Open Burners 004573 Burner Front 004574 Burner Rear 004618 Burner Cap 037190 Inj

-32- Revision 3/F3601 8. PARTS DIAGRAM 8.1 MAIN ASSEMBLY G50C ILLUSTATED

-33- Revision 3/F3601 Pos Part no. Description 1 016511 TROUGH TRAY 2 016387 GRIDDLE ('A' OPTION) 016386 GRIDDLE ('B' OPTION)

-34- Revision 3/F3601 36 012776 CASTOR ASSEMBLY 015652 CASTOR YOKE 011046 WHEEL - 75mm 014854 WHEEL PIN 37 014873 LEG TUBE - ADJUSTABLE 014872

-35- Revision 3/F3601 9.2.2 GAS PIPING ASSEMBLY (UK only) 8.2 GAS PIPING ASSEMBLY G50C ILLUSTRATED 51OVEN PILOT DETAIL - VIEWED FROM REAR434445 384

-36- Revision 3/F3601 Pos Part no. Description 1 014803 HOB SUPPLY PIPE 2 011833 TEE - 3/4" 3 013473 NIPPLE - 3/4" HEX 4 011853 REGULATOR

-37- Revision 3/F3601 40 032150 OVEN INJECTOR Ø1.50mm - PROPANE GAS 032230 OVEN INJECTOR Ø2.30mm - NATURAL GAS 41 012254 INJECTOR SUPPORT BRACK

-38- Revision 3/F3601 9. SERVICE CONTACTS AUSTRALIA VICTORIA - MOFFAT PTY HEAD OFFICE AND MAIN WAREHOUSE 740 Springvale Road Tel (03) 9518 38

-39- Revision 3/F3601 UNITED KINGDOM BLUESEAL LTD Units 6-7 Mount St Tel 0121-327 5575 Business Park Fax 0121-327 9711 Birmingham B7 5QU

-4- Revision 3/F3601

-5- Revision 3/F3601 1. SPECIFICATIONS Dimensions shown in millimetres. LEGEND - Gas connection entry point - ¾” BSP male G50 A G50 B G50 C G50 D

-6- Revision 3/F3601 Dimensions shown in millimetres. LEGEND - Gas connection entry point - ¾” BSP male MODEL: G50-8 G50-8 A G50-8 C G50-8 B G50-8

-7- Revision 3/F3601 INSTALLATION CLEARANCES Non-Combustible Combustible Sides 0 mm 25 mm Back 25 mm 25 mm CATEGORY I2H, I3P HEAT INPUT Input

-8- Revision 3/F3601 It is important that this oven is installed correctly, and that the operation is correct before handing over to the user

-9- Revision 3/F3601 Location 1) It is important to have a minimum of 25mm (1") of air space at the rear and sides of the unit from